欢迎关注“一信泰质量”官方网站!

您当前的位置:网站首页 > 行业新闻 > IC认证标签的要求

IC认证标签的要求

加拿大IC认证中的无线产品认证标准RSP 100于2016年1月份发布了最新的Issue 11版本,其中标准对Label要求如下:

一: 通过IC认证的产品标签要求

应至少包含以下内容

1. 产品型号Product Marketing Name (PMN)

2. 硬件版本号Hardware Version Identification Number (HVIN)

3. 软件版本号Firmware Version Identification Number (FVIN)

4. 主产品型号Host Marketing Name (HMN)

标签要求

1. 产品型号和IC号码应永久固定在产品外观。

2. 产品型号,硬件版本号和IC号码可以以雕刻,丝印等方式体现在产品上或永久固定在产品不可拆卸的部件上。

3. 进入加拿大市场通过的产品型号,硬件版本号和IC号码等信息必须加入到REL(Radio Equipment List)列表中。

4. IC号码要求如下:

IC: XXXXXX-YYYYYYYYYYY

XXXXXX为公司代码CN Unique Product Number (UPN),最多只能6位。

YYYYYYYYYYY为产品唯一代码Unique Product Number (UPN) ,最多只能11位。

XXXXXX和YYYYYYYYYYY只能是大写字母A至Z,或数字0至9,或数字和字母的组合。

 

标准原文要求如下:

3.1  Labelling of Certified Products

It should be noted that the Product Marketing Name (PMN), Hardware Version Identification Number (HVIN), Firmware Version Identification Number (FVIN) and Host Marketing Name (HMN) are commonly used terms, and are defined in Section 10 of this document.

Every unit of certified product for marketing and use in Canada shall be identified as per these requirements:

  • The HVIN and ISED certification number shall be permanently indicated on the exterior of the product or displayed electronically according to e‑labelling requirements:
    • the HVIN and ISED certification number are permitted to be placed on a label, which shall be permanently affixed to the product
    • the ISED certification number shall be preceded by "IC:"
    • the HVIN is permitted to be listed or placed with or without any prefix (HVIN:, Model#, M/N:, P/N:, etc.)
    • the HVIN and ISED certification number are not required to be adjacent to each other
  • The PMN must be displayed electronically (e‑labelling), or indicated on the exterior of the product or product packaging or product literature, which shall be available with the product or online.
  • The PMN, HVIN and ISED certification number are permitted to be etched, engraved, stamped, printed on the product, or permanently affixed to a permanently attached part of the product.
  • The PMN, HVIN and ISED certification number indicated/displayed (e‑labelling) on any product on the Canadian market must be listed in the REL.
  • When the FVIN is the only differentiation between different product versions (PMN and HVIN remain identical) listed in the REL within a family certification, the FVIN shall be displayed electronically or stored electronically and be easily retrievable.
  • In all cases, the PMN, FVIN, HVIN and ISED certification number text shall be clearly legible.

Note: The ISED certification number, HVIN, applicable PMN and FVIN are not required to be adjacent to each other.

The certification number is made up of a Company Number (CN), assigned by Innovation, Science and Economic Development Canada's Certification and Engineering Bureau, followed by the Unique Product Number (UPN) assigned by the applicant. The certification number format is:

IC: XXXXXX-YYYYYYYYYYY

where:

  • The letters "IC:" indicate that this is an Innovation, Science and Economic Development Canada certification number, but they are not part of the certification number. XXXXXX-YYYYYYYYYYY is the ISED certification number.
  • XXXXXX is the CN assigned by Innovation, Science and Economic Development Canada. Newly assigned CNs will be made up of five numeric characters (e.g. “20001”) whereas existing CNs may consist of up to five numeric characters followed by an alphabetic character (e.g. “21A” or “15589J”).
  • YYYYYYYYYYY is the Unique Product Number (UPN) assigned by the applicant, made up of a maximum of 11 alphanumeric characters.
  • The CN and UPN are limited to capital alphabetic characters (A‑Z) and numerals (0‑9) only. The use of punctuation marks or other symbols, including "wildcard" characters, is not permitted.
  • The HVIN may contain punctuation marks or symbols but they shall not represent any indeterminate ("wildcard") characters.

二. 模组和主产品标签要求

除了要满足以上要求外,还应增加以下要求:

Contains IC: XXXXXX-YYYYYYYYYYY

XXXXXX-YYYYYYYYYY为通过认证的模组IC号码。

 

标准原文要求如下:

3.2 Module and Host Product Labelling Requirements

Any product for which Modular Approval (MA) or Limited Modular Approval (LMA) is being sought shall meet the above labelling requirements (Section 3.1).

The Host Marketing Name (HMN) must be displayed (according to e-labelling requirements) or indicated at any location on the exterior of the host product or product packaging or product literature, which shall be available with the host product or online.

The host product shall be properly labelled to identify the modules within the host product.

The Innovation, Science and Economic Development Canada certification label of a module shall be clearly visible at all times when installed in the host product; otherwise, the host product must be labelled to display the Innovation, Science and Economic Development Canada certification number for the module, preceded by the word “Contains” or similar wording expressing the same meaning, as follows:

Contains IC: XXXXXX-YYYYYYYYYYY

where: XXXXXX-YYYYYYYYYYY is the module’s certification number.

The applicant for a certified module shall provide with each certified module to the user, either a host label, such as described above, or an explanation and instructions to the user as to the host product labelling requirements.

上一篇文章:
下一篇文章:
关注我们
网站分享
网站统计
友情链接:ACBWLLCCCFCCIECEE
© CopyRight   2015-2018   深圳一信泰质量技术有限公司   版权所有   粤ICP备 15083430
地址:深圳市龙华新区清祥路1号宝能科技园6栋A座16楼   电话:0755-28230888   传真:0755-28230886   邮编:518109   邮箱:info@uttlab.com